MCI SERVICE INFORMATION

Cleaning up: Keeping your DPF in A1 shape

Your new MCI coach is equipped with the latest "clean-air" technology available to the market today. In addition to being mandated by the U.S. government, its use helps maintain a cleaner environment for all of us.

But, as with all new technologies, there is a short learning curve required in order to keep it functioning properly. Fortunately, it's fairly straightforward and easy. While the system is designed to operate for more than 150,000 miles without major service requirements, a periodic "cleaning" of the Diesel Particulate Filter (DPF) system is required to keep engine performance from suffering.

Most of this cleaning is done automatically as the coach is driven in its normal manner. However, certain sustained operating conditions can require a more interactive cleaning process. Luckily the system is also designed to alert the driver to its operation and service needs before they become critical and the engine shuts down, possibly requiring the coach to be towed.

Heed the lights, use the right fuel and oil

Failing to understand what is required to operate a DPF-equipped coach can be costly. The requirements aren't difficult to learn, but they are critical. First of all, it's vital that you use less than 15 PPM Ultra Low Sulfur Diesel (ULSD) fuel and low-ash oil, SAE rating CJ-4, in order to be EPA compliant. Additionally, failure to do so may result in shortened lifecycle of the DPF system.

Just as importantly, on your new coach, you should have noticed two or three new alert lights on your instrument panel, depending on your particular engine.

Training the driver to know and understand what the new dash telltale lights mean is extremely important: Acting on this information may save costly down time. These telltales are:

NO CHANGES TO TELLTALE LAMPS:	E/J/D Vansco	D Commuter I/O
Yellow Check Engine Lamp
Red Stop Engine Lamp
NEW TELLTALE LAMPS:
Regeneration Lamp (DPF)
High Exhaust Temperature Lamp (HET)
Malfunction Indicator Lamp (MIL)(Detroit Diesel Only)

What the operator needs to do when the new telltales are on.

WHEN YOU SEE THIS:			Action required
	or		High Exhaust Temperature light — no action required. This telltale is only active below 5 mph and when the exhaust temperature is greater than 750°F (400°C). This telltale can be on in conjunction with other DPF telltales.
	or		For coaches with Series 60 engines only. Indicates a malfunction within the emissions system. Seek service from a Detroit Diesel service facility.
	or		This indicates a regeneration is required. If possible, maintain road speed above 5 MPH  for a minimum of 20 minutes for the system to do an automatic regen. If this is not possible, and the DPF light is on solid, perform a stationary regen within 5-6 hours. If light is flashing, perform a stationary regen within 1-2 hours.

When the following combinations of telltale lights are on, ACTION MUST BE TAKEN!

WHEN YOU SEE THIS:
E /J / D Vansco		D Commuter I/O
and	or	and
Action required: Engine power is de-rated, regeneration required. Move the coach to a safe location and perform stationary regeneration within 30 minutes, or operate the coach above 5mph until the regen light goes out.
and and	or	and and
Action required: Engine power de-rated or engine shutdown has been engaged. Regeneration locked out and cannot be performed; service is required. Contact an authorized engine manufacturer for assistance. Red "check engine" appears SOLID first. Flashing indicates 30 seconds to shutdown. Once shut down, coach may need to be towed for service.

*** Towing required by manual regeneration is not covered under warranty ***

How to do a Parked or Stationary Regeneration

Note: Be sure that the tailpipe is clear of any combustible materials. Operator must remain with the coach during the entire stationary regeneration process
IMPORTANT: If there are any active engine codes, regeneration may be inhibited.

Engine coolant temperature must be above 140°F (60°C). Engine must be at curb idle, with fast idle OFF. Move and hold the regen switch to the "initiate" position for 5 seconds and release. Do not move the switch to the regen-disable position. Please verify switch is returned to the middle position for normal coach operation.

If regeneration is not initiated when the regen switch is held in the up position, cycle the park brake off and on, shift the transmission in and out of gear, and try again.

Regeneration switch located inside the right rear side service door.

Parked or Stationary Regeneration

DPF lamp will turn on for one second, then turn off for the duration of the regeneration.
Engine speed will rise to between 1400 and 1600 RPM.
HET telltale will illuminate after approximately 3 minutes and will stay illuminated for the duration of the regeneration. (This is a normal cautionary warning.)

Regeneration will last approximately 20 to 40 minutes, depending on the initial level of soot in the DPF.When the regeneration is complete, all telltales will be off and the engine RPM will return to idle. For coaches with CAT engines, the cooling fan will turn off, and a historical event code will be logged.

Be kind to your engine: Limit your idling time

If you have Proheat, use it! Extended idle time, depending on engine operating temperatures, may shorten the duty cycle of the regeneration process, and may be amplified during extreme cold weather conditions.

Proheat is not only used to maintain coolant temperature while the engine is running, it can be used as an engine pre-heater on cold days.

Turn Proheat on 30 minutes prior to engine startup depending on ambient temperature.

To turn Proheat on, hold the momentary dash-mounted rocker switch in the up position for 3 seconds. Proheat will run for approximately 90 minutes, or until battery voltage drops below 10 volts, the coach runs out of fuel or there is a fault code. Within the 90 minutes, Proheat will cycle on and off to maintain coolant temperature between 150 and 185 degrees Fahrenheit.

For proper maintenance of the Proheat system, please refer to Service Bulletin 2913.

Quick-reference cards are available from MCI customer service by calling 800-323-1290. For the D coach I/O systems, ask for 03-15-5871A. For E / J / D Vansco systems, request 03-15-5870A. For additional information, please see the latest version of MCI's Service Bulletins 2959, 2963, 2964, 2965, 2966 and 2969. The bulletins can be downloaded at http://service.mcicoach.com/ServiceInfo/ServiceBulletins.nsf

Whenever you are working on your coach, always consult your owners and / or maintenance manual for full instructions and follow all safety precautions. If you have additional questions that are not addressed in your maintenance manual, consult your nearest MCI Service Center or call MCI's Technical Call Center.